Search for products on our site
Your search for "milling machine" revealed the following:
-
Milling Machine Part - Feed Reverse Knob Stud Set
$ 29.95
Feed Reverse Knob Stud SetPN: PY-B-110/111/112
-
Milling Machine Part - Forward Reverse Switch for 2-SPEED MOTOR (High / Low)
$ 68.00
Milling Machine Part - Forward Reverse Switch for 2-SPEED MOTOR (High / Low)Forward High / Stop / Reverse High / Forward Low / Stop / Reverse Low Switch Can fit EISEN step pulley milling machine with 2-speed motor (S-2M 16-speed) and similar milling machines from Taiwan with 3-phase, 2-speed motorThe bolt hole pattern for the 4...
-
Chen Ying Manual Lubricator for Milling Machine (Pressure-relief type) CLAB-6
$ 68.00
Manual pump / Hand Oiler / One-Shot Lubrication UnitCommonly used on Bridgeport-type milling machines from Taiwan.Model: CLAB-6Volume per discharge: 8 ccMaximum discharge pressure: 15 kgf/cm2 (213.4 psi)Tank capacity 350 ccDischarge bore: 6mmMade in TaiwanFrequently Asked Questions:Question: Is the oil outputted when the handle is pulled or when it's returning?Answer: Lubrication oil is released when the...
-
Chen-Ying Manual Lubricator for Milling Machine (Pressure-relief type) CLAB-8
$ 36.00 $ 54.85
Manual pump / Hand Oiler / One-Shot Lubrication UnitCommonly used on Bridgeport-type milling machines from Taiwan.Model: Chen-Ying CLAB-8Volume per discharge: 8 ccMaximum discharge pressure: 15 kgf/cm2 (213.4 psi)Tank capacity 600 ccDischarge bore: 6mmMade in TaiwanFrequently Asked Questions:Question: Is the oil outputted when the handle is pulled or when it's returning?Answer: Lubrication oil is released when...
-
1/8 HP Filtered Coolant Pump, 110V/220V, SINGLE-PHASE, 180mm (7") SP-8180-1PH
$ 315.00
FLAIR SP-8180-220V-1PH 1/8 HP Immersion Coolant Pump for machine tool coolant tank This in-tank coolant pump is suitable replacement for many coolant pumps used on lathes, milling machines, grinders and other machinery.Brand: FLAIRCoolant output connection is NPT female 3/8”.Distance from flange to bottom is 180mm (7"). Max flow: 37 liter / min (9.7 GPM) Flow rate : 8.1...
-
VERTEX 3" Boring Head Set VBHC-R8-BC3-I for R8, 10~220mm capacity, Inch-spec
$ 525.00
VERTEX Boring Head Set VBHC-R8-BC3-IMarked dial face with 0.0005" graduationFor R8 spindle (Bridgeport mills)Maximum boring depth: 1.96" (50mm)Boring capacity: 0.39" ~ 8.66" (10mm~220mm)Boring head diameter: 3"Boring bar hole size: 3/4"Center distance between holes: 15/16" Offset: 1"Adjusting screw is hardened and ground.Sturdy boring unit of extended boring range, suitable for roughing cuts and featuring fine adjustment and high accuracy....
-
ALIGN( or Bestline) Power Feed for X-Axis AL-500PX (Latest model)
$ 455.00
Brand: ALIGN ( or Bestline)Made in TaiwanPower Table Feed for Bridgeport-style milling machines (For X-axis / Longitudinal )Model #: AL-500PXPX-series is the latest model. SX is the earlier model.* Variable speed control * Rapid traverse button* Automatic shut-off at end of cut* On-off switch* Travel stop/ limit switch assembly* Complete installation hardware included* Packaged in eco-friendly...
-
1/2 HP Suction-Type Coolant Pump, 220V/440V, 3PH, NPT 1" Outlet,MC-2000-3 FLAIR
$ 499.95
1/2 HP Cast Iron Suction-type Coolant PumpThis suction-type coolant pump is suitable replacement for many coolant pumps used on larger lathes, milling machines, grinders and other machinery.Coolant inlet: PT 1"Coolant outlet: PT 1"1/2 HP220 / 440V3 PHASEOutput: 120 Liter/min (32 GPM).Head lift: 16.3 meterMade in Taiwan.Customer reported this can act as replacement for Shibaura OPS-400...
-
Bando Timing Belt 225Lx25mm Bridgeport-type Milling Mechanical Variable speed
$ 34.95
Bando Synchronous Timing Belt 225L x 25mm WidthFor Bridgeport-type Mechanical Variable speed Milling MachineTotal Length: 225mm (8.85”)Width : 25mm (0.98")Parts Number : S2A-HTH#63
-
J-139 collet alignment screw and J-138 set screw
$ 34.95
1 set of J-139 collet alignment screw and J-138 set screw for S-2A, S-3A, S-3AB, S-3AII milling machines
